Optimization of chemical mechanical polishing parameters on surface roughness...
Industrial Lubrication and Tribology, Volume 66, Issue 6, Page 685-690, September 2014. Purpose – The purpose of this paper is to investigate the effects of abrasive contents, oxidizer contents, slurry...
View ArticleInvestigation of using Calabrian pine cone dust and borax in brake pads
Industrial Lubrication and Tribology, Volume 66, Issue 6, Page 678-684, September 2014. Purpose – The purpose of this paper is to investigate use of calabrian pine (pinus brutia) cone (CPC) dust along...
View ArticleTemperature rise characteristics of a new designed disc for inclined downward...
Industrial Lubrication and Tribology, Volume 66, Issue 6, Page 671-677, September 2014. Purpose – The aim of this work is to reveal the temperature rise characteristics of the new designed disc during...
View ArticlePreparation of SiO2 nanoparticles and investigation of its tribological...
Industrial Lubrication and Tribology, Volume 66, Issue 6, Page 662-670, September 2014. Purpose – The purpose of this work is to study tribological properties of liquid paraffin with SiO2 nanoparticles...
View ArticleWet multi-disc friction components heat dissipation capability and optimal...
Industrial Lubrication and Tribology, Volume 66, Issue 6, Page 653-661, September 2014. Purpose – The purpose of this study is to investigate wet multi-disc brake temperature field and optimal oil...
View ArticleInvestigation of carbon–carbon composite brake pads in wet and dry sliding...
Industrial Lubrication and Tribology, Volume 66, Issue 6, Page 645-652, September 2014. Purpose – The purpose of this study was to investigate wear behaviours of brake pads produced from carbon–carbon...
View ArticleTribology of drawing lubricants for low carbon steel
Industrial Lubrication and Tribology, Volume 66, Issue 6, Page 640-644, September 2014. Purpose – This paper aims to present a study of frictional characteristics of steel/die steel pair under sliding...
View ArticleEffects of antiwear additives in the base oil on the tribological performance...
Industrial Lubrication and Tribology, Volume 66, Issue 6, Page 633-639, September 2014. Purpose – The purpose of this study is to investigate the effects of zinc dialkyl dithiophophates (ZDDP) and...
View ArticleEnhanced tribological performance of CuS thin film on Si substrate: the case...
Industrial Lubrication and Tribology, Volume 67, Issue 1, February 2015. Purpose The purpose of this paper was to demonstrate the influence of APS (3-Aminopropyl-triethoxysilane)-PAA (Polyacrylic Acid)...
View ArticleThe importance of 2% PTFE/FeF3 additives in engine fully formulated oil for...
Industrial Lubrication and Tribology, Volume 67, Issue 1, February 2015. Purpose Phosphorus (P) and Sulfur (S) in engine oil are the main topics of this paper. Very reproducible boundary lubrication...
View ArticleDetermination of Optimum Particle Size of Al2O3/SiCp Reinforced Hybrid...
Industrial Lubrication and Tribology, Volume 67, Issue 1, February 2015. Purpose In this study, input parameters of particle size and applied load have been optimized to determine minimum weight loss...
View ArticleResearch on the tribological properties of a textured lubricating...
Industrial Lubrication and Tribology, Volume 67, Issue 1, February 2015. Purpose The purpose of this paper is to investigate the tribological properties of a textured lubricating wear-resistant coating...
View ArticleAnalysis of Wear Generation in Mine Excavator Bucket
Industrial Lubrication and Tribology, Volume 67, Issue 1, February 2015. Purpose The purpose of this paper is to explore the wear phenomena on the bottom surface of excavator bucket and optimize the...
View ArticleTribological problems in shaft hoist ropes wear process
Industrial Lubrication and Tribology, Volume 67, Issue 1, February 2015. Purpose The main practical purpose of described research was to create conditions for the correct decision concerning an...
View ArticleTribological Behaviours of Surface-modified Serpentine powder as Lubricant...
Industrial Lubrication and Tribology, Volume 67, Issue 1, February 2015. Purpose The aim of this paper is to study the tribological performance and self-repairing performance of surface-modified...
View ArticleStatic characteristics of thermohydrodynamic journal bearing operating under...
Industrial Lubrication and Tribology, Volume 67, Issue 1, February 2015. Purpose The purpose of this work is to investigate the static performance characteristics of thermohydrodynamic journal bearing...
View ArticleCFD analysis of load-carrying capacity of hydrodynamic lubrication on a...
Industrial Lubrication and Tribology, Volume 67, Issue 1, February 2015. Purpose Water-lubricated bearing is becoming more and more popular since it is environmentally friendly and saves energy....
View ArticleDry sliding friction and wear behavior of self-lubricating wollastonite...
Industrial Lubrication and Tribology, Volume 67, Issue 1, February 2015. Purpose The purpose of this paper is to investigate the friction and wear performance of pure polycarbonate (PC) and 5 %-30 %...
View ArticleResistance to cast iron seizure determined by the technological condition of...
Industrial Lubrication and Tribology, Volume 67, Issue 1, February 2015. Purpose Aim of this study was to evaluate a surface layer of the CONDITION resistance to seizure. The surface layer was shaped...
View ArticleMeasurement and prediction of the heat transfer properties of hydrocarbon...
Industrial Lubrication and Tribology, Volume 67, Issue 1, February 2015. Purpose Refined hydrocarbon distillate fractions are commonly used as base oils in aluminum sheet cold rolling applications. The...
View ArticleWater lubrication of PTFE composites
Industrial Lubrication and Tribology, Volume 67, Issue 1, February 2015. Purpose The paper presents results on the friction and the wear of PTFE and 8 commercially available composites with PTFE...
View Article
